Braun A5 User Manual download pdf (Page 13)

Page 11

57 – Outer barrier is not up and latched and ground

detect switch did not deactivate (Century and

Vista only)

58 – Outer barrier is not up and latched and the plat-

form is 3” above the ground

59 – Outer barrier is not up after pausing platform

travel

60 – Verify the IB occupied switch is functioning cor-

rectly when lift is below ﬂoor level. The kickout

gas springs are worn, replace before using

75 – Low voltage detected; must turn off power switch

to reset LCD

77 – Vehicle secure interlock has not been activated

90 – Position will be set if you keep holding the button

until it beeps

91 – Position is out of a predetermined acceptable

range of ﬂoor position

92 – Bridge switch is not made, needs adjusting

93 – Inner rollstop occupied switch is not made,

position needs to be moved or switch should be

adjusted

94 – Outer barrier is not made, ﬁx and try again

95 – Outer barrier latch is not made (check for jumper

on Century and Vista lifts, check latch on Millen-

nium lifts)

99 – Controller program is not valid; replace controller

Flashing Numbers

Flashing 65 – Unfold button is pressed

Flashing 66 – Fold button is pressed

Flashing 67 – Down button is pressed

Flashing 68 – Up button is pressed

Flashing 69 – Bridge switch is activated

Flashing 70 – Outer barrier latch switch is activated

Flashing 71 – Ground detect switch is activated

Flashing 72 – Outer barrier up switch is activated

Flashing 73 – Inner rollstop up switch is activated

Flashing 74 – Inner rollstop occupied switch is acti-

vated

Flashing 76 – Outboard barrier occupied switch is

activated

Flashing 78 – Threshold tape switch “A” is activated

Flashing 79 – Threshold tape switch “B” is activated

Flashing 80 – Position set button is pressed

LCD Lift Codes

Listed below are codes that the lift controller outputs

during lift operation. The codes will be displayed

on an LCD screen located on the lift control board

inside the pump module. See the Manual Operating

Instructions in the operator's manual for pump cover

removal instructions.

Non-Flashing Numbers

01 – Platform stowed

02 – Platform unfolding

03 – Platform unfolding paused

04 – Platform at ﬂoor level

05 – Platform beginning to lower

06 – Platform lowering (threshold cannot be occu-

pied from this point down)

07 – Outer barrier moving to horizontal position

08 – Platform at ground level

09 – Outer barrier moving to vertical position

10 – Platform raising

11 – Platform raising paused at ﬂoor

12 – Platform folding (limited pressure)

13 – Platform folding (full pressure)

14 – Timed fold (cinching lift tite) or (anti-rattle state)

15 – Platform folding stopped

16 – Paused fold

17 – Platform between ground and 3” above ground

18 – Platform above 3”

19 – Outer barrier moving to horizontal postion

23 Outer barrier going back down after occupant

detected

28 – Illegal function/not deﬁned

29 – Interlock fault not recognized (or has been

cleared but a motion button is still pressed)

30 – Platform location unknown

31 – Platform location transition state; attempting to

locate position

35 – Two or more motion buttons are being pressed

36 – The retention belt cannot be buckled while try-

ing to fold or unfold

37 – Motion button being pressed is not a valid mo-

tion

50 – Outer barrier is not up above inboard barrier

locked position

51 – Threshold is occupied when platform is 1” or

more below ﬂoor level

52 – Inner rollstop is not up and locked below inner

rollstop locked position

53 – Inner rollstop occupied sensor is not activated

between ﬂoor and inner rollstop up position

54 – Outer barrier is occupied before it is up

55 – Outer barrier is not latched when above the in-

ner rollstop locked position (Millennium only)

56 – Outer barrier is not up and latched and bridge

switch did not deactivate

1 ... 12 13 14 ... 30

Comments to this Manuals

No comments

Braun A5 User Manual Page 13

Comments to this Manuals

Related products and manuals for Unknown Braun A5