Braun A5 User Manual download pdf (Page 15)

Page 13

Maintenance and Lubrication Schedule

Maintenance and

lubrication procedures

must be performed as

speciﬁed by an

authorized service

technician. Failure to

do so may result in

serious bodily injury

and/or property

damage.

Proper maintenance is necessary to ensure safe,

troublefree operation. Inspecting the lift for any wear,

damage or other abnormal conditions should be a part

of all transit agencies’s daily service program. Simple

inspections can detect potential problems.

The maintenance and lubrication procedures speciﬁed

in this schedule must be performed by a Braun autho-

rized service representative at the scheduled intervals

according to the number of cycles.

Braun dual parallel arm lifts are equipped with hard-

ened pins and self-lubricating bushings to decrease

wear, provide smooth operation and extend the service

life of the lift.

When servicing the lift at the recommended intervals,

inspection and lubrication procedures speciﬁed in

the previous sections should be repeated. Clean the

components and the surrounding area before apply-

ing lubricants. LPS2 General Purpose Penetrating

Oil is recommended where Light Oil is called out.

Use of improper lubricants can attract dirt or other

contaminants which could result in wear or damage

to the components. Platform components exposed to

contaminants when lowered to the ground may require

extra attention.

Lift components requiring grease are lubricated during

assembly procedures. When these components are

replaced, grease must be applied during installation

procedures. Speciﬁed lubricants are available from

The Braun Corporation (part numbers provided above).

All listed inspection, lubrication and maintenance

procedures should be repeated at “750 cycle” intervals

following the scheduled

“4500 Cycles” mainte-

nance. These intervals

are a general guideline

for scheduling mainte-

nance procedures and

will vary according to

lift use and conditions.

Lifts exposed to severe

conditions (weather, envi-

ronment, contamination,

heavy usage, etc.) may

require inspection and

maintenance procedures

to be performed more

often than speciﬁed.

Maintenance Indicator: The Lift Ready green LED

mounted on top of the pump cover will begin to blink

after every 750 cycles. The blinking LED will not affect

the functions of the lift, but is a reminder to complete

necessary maintenance and lubrication.

Once the lift has been serviced, fully stow the lift. Once

stowed, press the UP button on the hand pendant and

the Floor Level Set button on the back side of the pump

cover until the Lift Ready green LED stops blinking.

Discontinue lift use immediately if maintenance and

lubrication procedures are not properly performed, or if

there is any sign of wear, damage or improper opera-

tion. Contact your sales representative or call The

Braun Corporation at 1-800-THE LIFT

. One of our

national Product Support representatives will direct you

to an authorized service technician who will inspect your

lift.

RNING

750

Cycles

continued

Outer barrier link pivot points (2)

Outer barrier link slots (2)

Gear link assembly bearings (4)

Gear link assembly teeth (2)

Outboard platform bearings (2)

Platform fold link bearings (6)

Platform fold gear rack bearings (4)

Platform fold gear rack teeth (2)

Lift-Tite

™

latches (tower pivot points - 2)

Lift-Tite

™

latch gas (dampening) spring pivot

points (2 springs - 4 points)

Apply Light Oil - See Lubrication Diagram

Apply Light Grease - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

Apply Door Ease - See Lubrication Diagram

Apply Light Grease - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

Apply Light Grease - See Lubrication Diagram

Apply Door Ease - See Lubrication Diagram

Apply Light Oil - See Lubrication Diagram

1 ... 14 15 16 ... 30

Comments to this Manuals

No comments

Braun A5 User Manual Page 15

Comments to this Manuals

Related products and manuals for Unknown Braun A5